Peekaboo Project Pouches

January 18, 2019By Mister DomesticDIY, Projects, Sewing 5 Comments Opinion by Paid Consultant

As 2019 approached, I basically had organization on the brain. On the tail end of deep dive cleaning my sewing room, I suddenly felt that I needed quilted project pouches for my WIPs (Works in Progress). And if I needed them, I’m thinking that many of y’all out there might need them too. And even though I used a quilted panel in my tutorial, you can totally make these non-quilted, which would make them even easier than they already are.

What you’ll need:

  • 10” x 18” quilted panel
  • 10” x 10” clear vinyl (I used 10 gauge)
  • 8” zipper

Machine Used:

Preparing the Zipper

If you have an 8” zipper, then you can skip this section. I’m very much a proponent of using what you have, and any type of zipper would work for this project. I had a separating sports zipper that worked with the fabrics, so I used that. It was a little longer than I needed, so I needed to secure the zipper at the length I needed before trimming to size.

  • From the quilted panel, cut two 10” strips: one 1.5” and one the width of the zipper.
  • Set your machine to a zigzag stitch with a length of 0 and width of 7mm (or the widest setting)
  • Measure the section of the zipper teeth to 8” and mark it. Center the zipper under the needle and stitch 10 times across the zipper and snip.
  • Trim the excess of the zipper, leaving 1” beyond the stitch on the zipper.

Preparing the Zipper Strip

  • Cut the zipper-width strip in half. Take one half and, right sides together, slowly sew the zipper and strip together just inside the stitch line. As long as you sew slowly, the needle should fit between the zipper teeth as you stitch over it. If this is new for you, use the hand crank and slightly shift the zipper if you meet resistance.
  • Fold the tab portion onto the seam allowance and top stitch 1/8” from the seam.
  • Trim excess, leaving between 1/8” and 1/4”.
  • Compare the length of the zipper strip to the other strip and trim any excess until they are the same length.

Attaching the Zipper

  • Right sides together, sew the zipper strip and regular strip together using a 1/4” seam allowance. Using a zipper foot is recommended.
  • Fold the regular strip onto the seam allowance and top stitch 1/8” from the seam.
  • Trim excess, leaving between 1/8” and 1/4”.
  • Follow the same process to sew the zipper tab to the remaining quilted panel.

Constructing the Body


When working with vinyl or leather, I use a roller or a non-stick foot that will keep it from sticking to the presser foot. If the vinyl sticks underneath or you don’t have this foot, placing paper underneath as you sew will allow it to slide through with ease and could be torn away after the sewing is complete.

  • Line the vinyl up with one of the 10” sides of the panel with the vinyl on top. Clip in place and sew using a 1/4” seam allowance.
  • Fold the fabric portion onto the seam allowance and top stitch 1/8” from the seam. Trim excess, leaving between 1/8”.
  • Follow the same process with the other two raw ends. You will need to push the fabric out of the way as you topstitch.

  • Flatten the body and press folds into the top and bottom. The bottom should be approximately 1” and the top will be whatever the natural excess.
  • Using a 1/4” seam allowance, sew up both sides.
  • Using a zigzag stitch with 6 mm width and 1.4” length, sew both sides, encasing the raw edges.
  • Turn right-side out and enjoy your new project pouch.

So, here’s to starting out 2019 with an easy way to organize your Works in Progress. And, they’re so quick to make, that you can pay it forward by making some for your friends and family as well.

Keep it positive y’all. Mister Domestic out.

Print Friendly

5 Comments

  • Love this !…and just in time for the retreat I am going to next Friday. My projects will be so fancy in these bags. I like that I will be able to see them. I may make more than one. Thank you !<3

  • I made two of these project bags today. I wasn’t sure which batting I should use for the quilting so I tried 2 different types: the first was a thicker foam type and the other was batting for wall hangings. I will use the thinner, more pliable one next bag as I plan on making 3 more. I used bias binding to hide the seams but I probably will serge them next time. I found the extra layer made the corners too bulky to turn right side out. I enjoyed the tutorial and might be able to make the bag in 20 minutes by the time I finish a few more. Was the time to quiltthe fabric included in the time?

Leave a Reply

Your email address will not be published. Required fields are marked *